Weatherproof WoodCream 1L – Soft Finish – Rubio Monocoat NZ Limited

How to prepare interior wood before oiling?

Wood that you want to finish with oil must be thoroughly sanded, even new wood. It's important you make sure that the surface is completely scratch-free. In case of renovation, all previous treatments should first be completely removed. We recommend you end with a screening net P100 (floors), P100 - P150 (furniture, stairs, worktops, ...) or P150 (MDF, Valchromat, Finsa boards). The final sanding grit will determine the end result. The smoother you sand, the less oil can penetrate in the wood and less intense the colour (and protection) will be.

Preparation products

After the sanding process, you need to remove all the dust. You can do this by vacuum cleaning and by using Rubio Monocoat Cleaner. This product removes all the microdust that is left and prevents the oil from bonding with the dust instead of the wood fibres.

Depending on your goal or wooden support, you can use one of our other preparation products:

WoodPrep: use this product instead of Cleaner to achieve deeper colors or to minimise sanding errors. The product avoids (or reduces) the potential for visible sanding swirls, provides a more consistent and even colour penetration in case of uneven sanding and a more consistent colour penetration on naturally blotchy wood species ( e.g. maple).
Tannin Primer: use this product instead of Cleaner in case you're treating horizontal tannic woods (e.g. oak, chestnust, ...) that are often subjected to liquids. This product will prevent that tannin marks will appear on the surface. Be aware that this product, just like WoodPrep, will raise the wood fibres, so you'll achieve a more intensely coloured end result.
Deep Cleaner: use this product instead of Cleaner in case you're working with greasy (tropical) hardwoods ( e.g. teak, iroko, merbau, Afzelia, Afrormosia, ...). Deep Cleaner can also be used as a preparation when you need to re-oil in case of renovation. We advise you to wear gloves when using Deep Cleaner.

Notes:

Don't use any preparation or pre-treatment product in case you're working with MDF, Valchromat or Finsa boards.
When making colour samples, it is essential to mimic the sanding and preparation process that will be performed on the actual project, regardless if it is a wooden floor or a wooden table.

Optional pre-treatments

Once the wooden surface has been sanded down and prepared, you can choose to treat it with one of our optional pre-treatments:

Now the surface is fully ready to be finished off with our two-component Oil Plus 2C.

How to apply Pre Colour on furniture and stairs?

PreColour is a pre-colour, designed to always be used in combination with the Oil Plus 2C, to create special effects and contrasts. Enjoy unlimited creative possibilities thanks to the option to combine 14 different colours of PreColour (which can be mixed with one another) with a finish in one of the 40 colours of the Oil Plus 2C. At the same time, the optimal molecular bonding of the Oil Plus 2C with the wood remains guaranteed.

Instructions to apply PreColour on interior furniture and stairs

Step 1: Sand the surface
Step 2: Vacuum thoroughly and clean with Rubio Monocoat Cleaner
Step 3: Apply PreColour
Step 4: Allow the surface to dry for ± 12 hours
Step 5: Break the raised wood fibers
Step 6: Finish off with Oil Plus 2C

Step 1: Sand the surface

Sand the surface scratch-free. Finish with screening net 100 to 150. (When renovating, you must remove all the residues from previous treatments completely.)

Step 2: Vacuum thoroughly and clean with Cleaner

Vacuum thoroughly, eliminate remains of dust with Cleaner and wait until the surface is completely dry.

Step 3: Apply PreColour

Stir the product thoroughly and regularly with a stirring stick.
Apply an amount of PreColour with the Rubio Monocoat Brush and spread out using a red Scrubby Pad.
Wipe out evenly with a lint-free cloth.Tip 1: work in small areas to avoid overlapping.Tip 2: for smaller objects and corners you can also use the green Mouse Pad.

Step 4: Allow the surface to dry for ± 12 hours

The exact drying time depends on the support, moistening, temperature and ventilation.

Step 5: Break the raised wood fibers

After drying, break the raised wood fibres with a red Scrubby Pad and vacuum afterwards.

Step 6: Finish off with Oil Plus 2C

Now apply Oil Plus 2C (A + B component). Read our application instructions carefully.
Tip: in combination with PreColour it is best to use a white Scrubby Pad to apply Oil Plus 2C instead a beige or red one.

- To determine the correct colour, always do a small test first with one of our 20 ml sample bottles on identical sanded and prepared wood.

- When using several containers at one site, it is required to mix them for an even result.

- Do not use in combination with water-based finishing products, such as Invisible Protector.

How to apply Pre-Aging on floors

Pre-Aging is a high-quality, non-reactive pre-treatment that creates the look of reactive stains, but without the drawbacks. It is always combined with Oil Plus 2C. Pre-Aging is available in 10 standard colours, ranging from a lighter to a darker smoked look, including the warm, green/brown undertones that are so popular. All colours can be mixed with each other, so that the customer can get exactly what they want.

Instructions to apply Pre-Aging on floors

Step 1: Sand the surface
Step 2: Vacuum thoroughly
Step 3: Apply Pre-Aging
Step 4: Allow the surface to dry for ± 24 hours
Step 5: Break the raised wood fibers
Step 6: Finish off with Oil Plus 2C or Invisible Protector

Step 1: Sand the surface

Sand the surface scratch-free. Finish with screening net 100. (When renovating, you must remove all the residues from previous treatments completely.)

Step 2: Vacuum thoroughly

Vacuum thoroughly and eliminate all remains of dust.

Step 3: Apply Pre-Aging

Shake the Pre-Aging well before use and pour in a bucket (Rubio Monocoat Bucket).
Work in areas of ± 90 cm. Apply the product evenly and in a saturated manner on the to be treated surface with a Microfiber Pad.Tip: for edges/corners: apply with a brush or a green Mouse Pad.
Afterwards smooth out the area with the same Microfiber Pad. Make sure the pad is thoroughly wrung out. Avoid puddle formation.

Step 4: Allow the surface to dry for ± 24 hours

Allow to dry for about 24 hours and ensure sufficient ventilation.
The exact drying time depends on the support, air humidity, temperature and ventilation.

Step 5: Break the raised wood fibers

After drying, break the raised wood fibers with a floor polisher equipped with a red Pad and vacuum afterwards.

Step 6: Finish off with Oil Plus 2C or Invisible Protector

Now apply Oil Plus 2C or Invisible Protector.

- To determine the correct colour, always do a small test first with one of our 20 ml sample bottles on identical sanded and prepared wood.

- When using several containers at one site, it is required to mix them for an even result.

- Switch off the floor heating 48 hours before application.

- To avoid overlapping, always work wet-on-wet.

- On resinous wood species small white stains may appear as a reaction of the product to the wood.

How to apply Pre-Aging on furniture, stairs & worktops

Instructions to apply Pre-Aging on interior furniture, stairs & worktops

Step 1: Sand the surface
Step 2: Vacuum thoroughly
Step 3: Apply Pre-Aging
Step 4: Allow the surface to dry for ± 24 hours
Step 5: Break the raised wood fibers
Step 6: Finish off with Oil Plus 2C or Invisible Protector

Step 1: Sand the surface

Sand the surface scratch-free. Finish with screening net 100 to 150. (When renovating, you must remove all the residues from previous treatments completely.)

Step 2: Vacuum thoroughly

Vacuum thoroughly and eliminate all remains of dust.

Step 3: Apply Pre-Aging

Shake the Pre-Aging well before use and pour in a bucket (Rubio Monocoat Bucket).
Apply the product evenly and in a saturated manner on the to be treated surface with a Rubio Monocoat tool, such as a Microfiber Pad, Brush, Sponge, spray gun or roller.Tip: for edges/corners: apply with a brush or a green Mouse Pad.
Afterwards smooth out with a beige Scrubby Pad. Avoid puddle formation.

Step 4: Allow the surface to dry for ± 24 hours

Allow to dry for about 24 hours and ensure sufficient ventilation.
The exact drying time depends on the support, air humidity, temperature and ventilation.

Step 5: Break the raised wood fibers

After drying, break the raised wood fibers with a red Scrubby Pad and vacuum afterwards.

Step 6: Finish off with Oil Plus 2C or Invisible Protector

Now apply Oil Plus 2C or Invisible Protector.

- To determine the correct colour, always do a small test first with one of our 20 ml sample bottles on identical sanded and prepared wood.

- When using several containers at one site, it is required to mix them for an even result.

- To avoid overlapping, always work wet-on-wet.

- On resinous wood species small white stains may appear as a reaction of the product to the wood.

How to apply Precolor Easy on floors

Precolor Easy is a pre-colour, designed to always be used in combination with the Oil Plus 2C, to create special effects and contrasts. Enjoy unlimited creative possibilities thanks to the option to combine 14 different colours of Precolor Easy (which can be mixed with one another) with a finish in one of the 40 colours of the Oil Plus 2C. At the same time, the optimal molecular bonding of the Oil Plus 2C with the wood remains guaranteed.

Instructions to apply Precolor Easy on interior floors

Step 1: Sand the surface
Step 2: Vacuum thoroughly and clean with Cleaner
Step 3: Tape off areas
Step 4: Apply Precolor Easy
Step 5: Allow the surface to dry for ± 12 hours
Step 6: Tape off the untreated areas
Step 7: Apply Precolor Easy
Step 8: Allow the surface to dry for ± 12 hours
Step 9: Break the raised wood fibers
Step 10: Finish off with Oil Plus 2C

Step 1: Sand the surface

Sand the surface scratch-free. Finish with screening net 100 to 150. (When renovating, you must remove all the residues from previous treatments completely.)

Step 2: Vacuum thoroughly and clean with Cleaner

Vacuum thoroughly, eliminate remains of dust with Cleaner and wait until the surface is completely dry.

Step 3: Tape off areas

Tape off areas of ± 90 cm, in the lengthwise direction of the boards.

Step 4: Apply Precolor Easy

Stir the product thoroughly and regularly with a stirring stick.
Apply an amount of Precolor Easy with the Microfiber Pad in one taped off area.
Make sure to use enough of the product to cover the whole area.
Afterwards smooth out the area again with the same Microfiber Pad (make sure the pad is thoroughly wrung out).
Now skip an area and do the same as in the first area. Finish off the whole room like this, always skipping one area.

Step 5: Allow the surface to dry for ± 12 hours

The exact drying time depends on the support, moistening, temperature and ventilation.
Remove the tape.

Step 6: Tape off the untreated areas

Now tape off the untreated areas.

Step 7: Apply Precolor Easy

Stir the product again and apply as described in step 4.
Repeat until the whole floor is treated.
Afterwards remove the tape.Tip: step on the already dried out areas to remove the tape.

Step 8: Allow the surface to dry for ± 12 hours

The exact drying time depends on the support, moistening, temperature and ventilation.
Remove the tape.

Step 9: Break the raised wood fibers

After drying, break the raised wood fibers with a floor polisher equipped with a red Pad and vacuum afterwards.
Remove the tape.

Step 10: Finish off with Oil Plus 2C

Now apply Oil Plus 2C (A + B component). Read our application instructions carefully.
Tip: in combination with Precolor Easy it is best to use a white Pad to apply Oil Plus 2C instead a beige or red one.

- To determine the correct colour, always do a small test first with one of our 20 ml sample bottles on identical sanded and prepared wood.

- When using several containers at one site, it is required to mix them for an even result.

- Switch off the floor heating 48 hours before application.

- Do not use in combination with water-based finishing products, such as Invisible Protector.

- Difficult to apply on herringbone parquet.

How to apply Oil Plus 2C on interior furniture, stairs and countertops

Oil Plus 2C is a VOC-free hardwax oil of the newest generation which colours and protects your wood in one single layer. It's perfectly suitable for high traffic zones and can be applied to all interior wood surfaces (furniture, countertops, tabletops, stairs, walls, floors, etc.), almost all wood types and wood species (solid wood, veneer, MDF, etc.). The combination of the oil (A) and the Accelerator (B) guarantees a quick curing for optimal protection.

Instructions to apply Oil Plus 2C on interior furniture, stairs & countertops

Step 1: Sand the surface
Step 2: Vacuum thoroughly and clean with Cleaner
Step 3: Mix the two components (A and B) together
Step 4: Apply Oil Plus 2C
Step 5: Let it absorb for a few minutes and wipe away all excess oil
Step 6: Let it dry for 12-24 hours

Step 1: Sand the surface

Sand the surface scratch-free. Finish with screening net 100 to 150. (When renovating, you must first remove all the residues from previous treatments completely.)

Step 2: Vacuum thoroughly and clean with Cleaner

Vacuum thoroughly, eliminate remains of dust with Cleaner and wait until the surface is completely dry.

Step 3: Mix the two components (A and B) together

Stir the A component until a homogenous mixture is obtained. Carefully mix the two components (1 to 2 minutes) with a ratio of appr. 3 units A to 1 unit B.
Attention, the mixture of A and B can only be used during 4-6 hours. So be careful and only mix the amount you'll need in that timeframe.

Step 4: Apply Oil Plus 2C

Spread out a small quantity of Oil Plus 2C using a beige or red Scrubby pad or hand sander with a small beige 5.9 inch Pad (you can also use the Mouse Pad for smaller objects and corners).Spatula method: spread the Oil Plus 2C out with a stainless spatula in zones which can be finished within maximum 30 minutes (next step included!)For ceilings and walls you can use our Brush and beige Scrubby pad to spread out the oil

Step 5: Let it absorb for a few minutes and wipe away all excess oil

Let absorb during a few minutes. Wipe away all excess oil with a cloth or a hand sander with a small white 5.9 inch pad. Finish off with a cloth within max. 30 minutes. The surface should feel non-sticky!

Step 6: Let it dry for 12-24 hours

Let dry the surface for 12 to 24 hours and wait at least 5 days to clean with water and Surface Care or All Natural Wood Cleaner Spray.

Cloths and other tools which are saturated with oil may spontaneously combust. After usage, they need to be soaked in water before disposal.

- To determine the correct colour, always do a small test first with one of our 20 ml sample bottles on identical sanded and prepared wood.

- When using several containers at one site, it is required to mix them for an even result.

- After application the surface may appear a bit glossy. This will disappear after cleaning 2-3 times with Surface Care or All Natural Wood Cleaner Spray.

- Only use our maintenance and cleaning products.

- For greasy wood species ( e.g. Teak, Iroko, Kambala, Wengé, Eucalyptus, Merbau, Afzelia, Afrormosia, etc.), use Deep Cleaner instead of Cleaner.

- Tannin Primer can be used before applying the Oil Plus 2C for horizontal surfaces often subjected to liquids such as worktops or bathroom furniture.

How to apply Oil Plus 2C on floors

Instructions to apply Oil Plus 2C on floors

Step 1: Sand the surface
Step 2: Vacuum thoroughly and clean with Cleaner
Step 3: Mix the two components (A and B) together
Step 4: Apply Oil Plus 2C
Step 5: Let it absorb for a few minutes and wipe away all excess oil
Step 6: Pass again with a new white Rubio Monocoat Pad
Step 7: Let the surface dry for 12 - 24 hours

Step 1: Sand the surface

Sand the surface scratch-free. Finish with screening net 100. (When renovating, you must first remove all the residues from previous treatments completely.)

Step 2: Vacuum thoroughly and clean with Cleaner

Vacuum thoroughly, eliminate remains of dust with Cleaner and wait until the surface is completely dry.

Step 3: Mix the two components (A and B) together

Stir the A component until a homogenous mixture is obtained. Carefully mix the two components (1 to 2 minutes) with a ratio of appr. 3 units A to 1 unit B.
Attention, the mixture of A and B can only be used during 4 - 6 hours. So be careful and only mix the amount you'll need in that timeframe.

Step 4: Apply Oil Plus 2C

Work in zones of 5 - 10 m². Start each zone by treating the borders with a beige or red Scrubby pad. Then apply a small quantity of Oil Plus 2C every other 0,5 meters using a brush. Spread out plank-wise using a polishing machine with a beige or red 16 inch pad.

*Spatula method: Spread out Oil Plus 2C with a stainless spatula in zones which can be finished in maximum 30 minutes (including steps 5 and 6).

Step 5: Let it absorb for a few minutes and wipe away all excess oil

Thoroughly remove all excess oil with a cloth or a polishing machine with a white 16 inch pad. The surface should feel non-sticky!

Step 6: Pass again with a new white Pad

After having finished all the zones, pass again with a new white pad. Now the surface should feel non-sticky.

Step 7: Let the surface dry for 12 - 24 hours

Let the surface dry for 12 to 24 hours and wait at least 5 days to clean with water and Universal Soap or All Natural Wood Cleaner.

Cloths and other tools which are saturated with oil may spontaneously combust. After usage, they need to be soaked in water before disposal.

- To determine the correct colour, always do a small test first with one of our 20 ml sample bottles on identical sanded and prepared wood.

- When using several containers at one site, it is required to mix them for an even result.

- Only use our maintenance and cleaning products.

- After application the surface may appear a bit glossy. This will disappear after cleaning 2 - 3 times with Universal Soap or All Natural Wood Cleaner.

- For greasy wood species (e.g. Teak, Iroko, Kambala, Wengé, Eucalyptus, Merbau, Afzelia, Afrormosia, etc.), use Deep Cleaner instead of Cleaner.

How to apply Oil Plus 2C on interior furniture, stairs and countertops

Instructions to apply Oil Plus 2C on interior furniture, stairs & countertops

Step 1: Sand the surface
Step 2: Vacuum thoroughly and clean with Cleaner
Step 3: Mix the two components (A and B) together
Step 4: Apply Oil Plus 2C
Step 5: Let it absorb for a few minutes and wipe away all excess oil
Step 6: Let it dry for 12-24 hours

Step 1: Sand the surface

Sand the surface scratch-free. Finish with screening net 100 to 150. (When renovating, you must first remove all the residues from previous treatments completely.)

Step 2: Vacuum thoroughly and clean with Cleaner

Vacuum thoroughly, eliminate remains of dust with Cleaner and wait until the surface is completely dry.

Step 3: Mix the two components (A and B) together

Stir the A component until a homogenous mixture is obtained. Carefully mix the two components (1 to 2 minutes) with a ratio of appr. 3 units A to 1 unit B.
Attention, the mixture of A and B can only be used during 4-6 hours. So be careful and only mix the amount you'll need in that timeframe.

Step 4: Apply Oil Plus 2C

Spread out a small quantity of Oil Plus 2C using a beige or red Scrubby pad or hand sander with a small beige 5.9 inch Pad (you can also use the Mouse Pad for smaller objects and corners).Spatula method: spread the Oil Plus 2C out with a stainless spatula in zones which can be finished within maximum 30 minutes (next step included!)For ceilings and walls you can use our Brush and beige Scrubby pad to spread out the oil

Step 5: Let it absorb for a few minutes and wipe away all excess oil

Let absorb during a few minutes. Wipe away all excess oil with a cloth or a hand sander with a small white 5.9 inch pad. Finish off with a cloth within max. 30 minutes. The surface should feel non-sticky!

Step 6: Let it dry for 12-24 hours

Let dry the surface for 12 to 24 hours and wait at least 5 days to clean with water and Surface Care or All Natural Wood Cleaner Spray.

Cloths and other tools which are saturated with oil may spontaneously combust. After usage, they need to be soaked in water before disposal.

- To determine the correct colour, always do a small test first with one of our 20 ml sample bottles on identical sanded and prepared wood.

- When using several containers at one site, it is required to mix them for an even result.

- After application the surface may appear a bit glossy. This will disappear after cleaning 2-3 times with Surface Care or All Natural Wood Cleaner Spray.

- Only use our maintenance and cleaning products.

- For greasy wood species ( e.g. Teak, Iroko, Kambala, Wengé, Eucalyptus, Merbau, Afzelia, Afrormosia, etc.), use Deep Cleaner instead of Cleaner.

- Tannin Primer can be used before applying the Oil Plus 2C for horizontal surfaces often subjected to liquids such as worktops or bathroom furniture.

How to repair or renovate my Oil Plus 2C treated surface?

Over time the Oil Plus 2C treated surface may show some wear. Indications for wear are a visible walking zone, a surface that is more stain-sensitive and remains wet for a longer time after cleaning. If the surface shows much wear and tear or it needs a colour repair, you need to re-apply Oil Plus 2C in the colour that the wood was originally treated with.

Note: If the wooden object is too much damaged or neglected, you will first need to sand the surface and end with the same screening grit as you initially finished your wooden object with.

Instructions

Step 1: Clean the surface with Deep Cleaner
Step 2: Rinse well with clean water
Step 3: Mix the two components (A and B) together
Step 4: Apply Oil Plus 2C
Step 5: Let it absorb for a few minutes and wipe away all excess oil
Step 6: Let it dry for 12 - 24 hours

Step 1: Clean the surface with Deep Cleaner

Dampen the surface with just water and using a mop or sponge.
Dilute the Deep Cleaner with water (5% Deep Cleaner to 95% water).
Scrub the area with the dilution and a nylon scrubbing brush in the lengthwise direction of the wood. Do this until the surface is clean and spot free.Note: for stubborn stains, repeat the treatment or use one of our stain removers ( Grease Remover, Limespot Remover or Tannin Remover).

Step 2: Rinse well with clean water

Remove the dissolved dirt with a mop and clean water until all the foam has disappeared and the surface looks clean again.
Allow the surface to dry well (± 30 minutes at a temperature of 20°C and in a well-ventilated room).

Step 3: Mix the two components (A and B) together

Stirr the A component until a homogenous mixture is obtained. Carefully mix the two components (1 to 2 minutes) with a ratio of appr. 3 units A to 1 unit B.
Attention, the mixture of A and B can only be used during 4 - 6 hours. So be careful and only mix the amount you'll need in that timeframe.

Step 4: Apply Oil Plus 2C

Spread out a small quantity of Oil Plus 2C using a beige or red Scrubby pad or hand sander with a small beige 5.9 inch Pad (you can also use the Mouse Pad for smaller objects and corners).

Step 5: Let it absorb for a few minutes and wipe away all excess oil

Let absorb during a few minutes. Wipe away all excess oil with a cloth or a hand sander with a small white 5.9 inch pad. Finish off with a cloth within max. 30 minutes. The surface should feel non-sticky!

Step 6: Let it dry for 12 - 24 hours

Let the surface dry for 12 to 24 hours and wait at least 5 days to clean with water and Universal Soap, Surface Care, All Natural Wood Cleaner or All Natural Wood Cleaner Spray.

Cloths and other tools, saturated with oil, may spontaneously combust. After usage, they need to be soaked in water before disposal.

- When using several containers at one site, it is required to mix them for an even result.

- After application the surface may appear a bit glossy. This will disappear after cleaning 2 - 3 times with Universal Soap, Surface Care, All Natural Wood Cleaner or All Natural Wood Cleaner Spray.

- Only use our maintenance and cleaning products.

Can SheenPlus be applied on raw wood?

No. SheenPlus must be applied over Oil Plus 2C.

Will applying multiple layers of SheenPlus increase the sheen level?

No. SheenPlus is a monocoat product and only requires 1 single application. Adding another application of SheenPlus will not increase the sheen further.

How soon can I apply SheenPlus after Oil Plus 2C has been applied?

SheenPlus can be applied 24 hours after application of Oil Plus 2C.

Can I use SheenPlus Part A only?

No. It is mandatory to use SheenPlus Part A and Part B together.

Can SheenPlus be applied over Universal Maintenance Oil or Refresh Eco?

No. SheenPlus must always be applied on wooden surfaces just treated with Oil Plus 2C.

Can I finish off PreColour with Invisible Protector?

No.

How can I add more sheen to my surface treated with Oil Plus 2C?

SheenPlus can be applied over Oil Plus 2C (after minimum 24 hours) to increase the sheen level. Attention: SheenPlus can't be applied to raw wood.

How to handle stains?

Although many stains can be removed with Universal Soap, Surface Care, All Natural Wood Cleaner or All Natural Wood Cleaner Spray, Rubio Monocoat also developed a number of specific stain removers. Stubborn lime stains can be handled effectively with Limespot Remover, grease stains with Grease Remover and black/tannin stains with Tannin Remover. If the stain has penetrated the wood too deeply, the spot can be sanded and re-oiled.

First select the most suitable stain remover for your spots.

Is Oil Plus 2C food safe?

Technically, this asks if the product is safe to ingest, but we understand what you're getting at.

While we do not recommend ingesting our products, it can be safely used on a food contact surface. We even have a Food Contact Compliance from an independent testing institute (Eurofins).

How can I achieve a raw wood effect indoors?

To achieve a raw wood effect, the recommendations depend on your type of wood.

Even though we have a non-pigmented/transparent variant in the Oil Plus 2C range, called "Pure", this does not quite keep the natural colour for all wood types.

Oil Plus 2C is a linseed oil based product. Linseed oil has a naturally occurring colour to it which will enrich/darken the wood compared to its raw state.

Here are common solutions to neutralise the richening that occurs when applying oil-based finish to a few popular wood types:

White Oak: you can use the colour "Smoke 5%", "Natural" or "White 5%"
Red Oak: you can use Precolor Easy "Mint White" to neutralise the pink/red tones of the red oak and then apply the Oil Plus 2C "White 5%" to it.
Walnut: (because it is so dark on its own) you can use "Pure" to keep it looking as close to unfinished as possible. A slight darkening will occur, but this is typically desired.
Softwood (beech, maple, pine, ...): use Oil Plus 2C "White 5%" or "Natural"
Chestnut: use Oil Plus 2C "Smoke 5%"

If you are looking for an effective solution for all types of wood (including darker wood types) Invisible Protector is a very good alternative.

We always advise to do a test first.

What is the difference between Oil Plus 2C "Pure" and "Natural"

Simply put, Pure contains no pigment and Natural contains a creamy whitish/yellowish pigment.

Which one is clear? Neither. While Pure contains no pigment, clear is not the best description because Oil Plus 2C is a linseed oil based product. Linseed oil has a naturally occurring colour to it, which will enrich/darken the wood compared to its raw state.

Keeping your wood looking natural requires introducing just enough pigment to off-set the enriching/darkening caused by using an oil-based finish. This depends on the type of wood.

How do I know whether the surface is sufficiently dry after treatment?

Respect a minimum drying time of 12 to 24 hours while ensuring sufficient ventilation. Afterwards you can use the surface again.

When in doubt, use a cotton cloth and rub an inconspicuous area. If no oil sticks to the cloth, the surface is sufficiently dry.

However, wait until day 5, until the oil has completely cured, to clean with water for the first time. Until then, be careful with liquids.

How do I know whether the surface is sufficiently dry after treatment?

Respect a minimum drying time of 12 to 24 hours while ensuring sufficient ventilation. Afterwards you can use the surface again.

When in doubt, use a cotton cloth and rub an inconspicuous area. If no oil sticks to the cloth, the surface is sufficiently dry.

However, wait until day 5, until the oil has completely cured, to clean with water for the first time. Until then, be careful with liquids.

Topic heading

Descriptive topic content body text

Wood Preparation & Pre-treatments

Prepare your timber before you coat

Rubio Monocoat WoodCream

Rubio Monocoat WoodCream

You may also like

Choose options

Change country